6.1.3.17 IfcDoorStandardCase

Tür - Standard
porte standard

The standard door, IfcDoorStandardCase, defines a door with certain constraints for the provision of operation types, opening directions, frame and lining parameters, and with certain constraints for the geometric representation. The IfcDoorStandardCase handles all cases of doors, that:

HISTORY  New entity in IFC4.

Geometric Representations

The geometric representation of IfcDoorStandardCase is defined using the following multiple shape representations for its definition:


Common Use Definitions

The following concepts are inherited at supertypes:

 Instance diagram

Object Typing

The Object Typing concept applies to this entity as shown in Table 125.
TypeDescription
IfcDoorType 
IfcDoorStyle
NOTE This type is deprecated

Table 125 — IfcDoorStandardCase Object Typing



Profile 3D Geometry

The Profile 3D Geometry concept applies to this entity.

The door profile is represented by a three-dimensional closed curve within a particular shape representation. The profile is used to apply the parameter of the parametric door representation. The following attribute values for the IfcShapeRepresentation holding this geometric representation shall be used:

The following additional constraints apply to the 'Profile' representation type:

 

standard door
EXAMPLE  Figure 187 illustrates applying the door lining parameters to the door profile shape representation. The profile defines the outer boundary to which the door lining parameters relate as:
  • IfcDoorLiningProperties.LiningDepth starting at distance defined by LiningOffset going into the positive y direction.
  • IfcDoorLiningProperties.LiningThickness offset into the inner side of the rectangle.
  • IfcDoorLiningProperties.LiningOffset distance along the positive y direction to where the LiningDepth applies.
  • IfcDoorLiningProperties.ThresholdThickness starting at the bottom edge of the rectangle into the inner side of the rectangle
  • IfcDoorLiningProperties.ThresholdDepth starting at distance defined by LiningOffset going into the positive y direction.
  • IfcDoorLiningProperties.TransomOffset starting at the bottom edge of the rectangle (along local x axis) into the inner side of the rectangle, distance provided as percentage of overall height. Distance to the centre line of the transom.

Figure 187 — Door profile

 



XSD Specification:

 <xs:element name="IfcDoorStandardCase" type="ifc:IfcDoorStandardCase" substitutionGroup="ifc:IfcDoor" nillable="true"/>
 <xs:complexType name="IfcDoorStandardCase">
  <xs:complexContent>
   <xs:extension base="ifc:IfcDoor"/>
  </xs:complexContent>
 </xs:complexType>

EXPRESS Specification:

ENTITY IfcDoorStandardCase
SUBTYPE OF IfcDoor;
END_ENTITY;

Link to EXPRESS-G diagram EXPRESS-G diagram

Inheritance Graph:

ENTITY IfcDoorStandardCase
ENTITY IfcRoot
GlobalId : IfcGloballyUniqueId;
OwnerHistory : OPTIONAL IfcOwnerHistory;
Name : OPTIONAL IfcLabel;
Description : OPTIONAL IfcText;
ENTITY IfcObjectDefinition
INVERSE
HasAssignments : SET OF IfcRelAssigns FOR RelatedObjects;
Nests : SET [0:1] OF IfcRelNests FOR RelatedObjects;
IsNestedBy : SET OF IfcRelNests FOR RelatingObject;
HasContext : SET [0:1] OF IfcRelDeclares FOR RelatedDefinitions;
IsDecomposedBy : SET OF IfcRelAggregates FOR RelatingObject;
Decomposes : SET [0:1] OF IfcRelAggregates FOR RelatedObjects;
HasAssociations : SET OF IfcRelAssociates FOR RelatedObjects;
ENTITY IfcObject
ObjectType : OPTIONAL IfcLabel;
INVERSE
IsDeclaredBy : SET [0:1] OF IfcRelDefinesByObject FOR RelatedObjects;
Declares : SET OF IfcRelDefinesByObject FOR RelatingObject;
IsTypedBy : SET [0:1] OF IfcRelDefinesByType FOR RelatedObjects;
IsDefinedBy : SET OF IfcRelDefinesByProperties FOR RelatedObjects;
ENTITY IfcProduct
ObjectPlacement : OPTIONAL IfcObjectPlacement;
Representation : OPTIONAL IfcProductRepresentation;
INVERSE
ReferencedBy : SET OF IfcRelAssignsToProduct FOR RelatingProduct;
ENTITY IfcElement
Tag : OPTIONAL IfcIdentifier;
INVERSE
FillsVoids : SET [0:1] OF IfcRelFillsElement FOR RelatedBuildingElement;
ConnectedTo : SET OF IfcRelConnectsElements FOR RelatingElement;
IsInterferedByElements : SET OF IfcRelInterferesElements FOR RelatedElement;
InterferesElements : SET OF IfcRelInterferesElements FOR RelatingElement;
HasProjections : SET OF IfcRelProjectsElement FOR RelatingElement;
ReferencedInStructures : SET OF IfcRelReferencedInSpatialStructure FOR RelatedElements;
HasOpenings : SET OF IfcRelVoidsElement FOR RelatingBuildingElement;
IsConnectionRealization : SET OF IfcRelConnectsWithRealizingElements FOR RealizingElements;
ProvidesBoundaries : SET OF IfcRelSpaceBoundary FOR RelatedBuildingElement;
ConnectedFrom : SET OF IfcRelConnectsElements FOR RelatedElement;
ContainedInStructure : SET [0:1] OF IfcRelContainedInSpatialStructure FOR RelatedElements;
ENTITY IfcBuildingElement
INVERSE
HasCoverings : SET OF IfcRelCoversBldgElements FOR RelatingBuildingElement;
ENTITY IfcDoor
OverallHeight : OPTIONAL IfcPositiveLengthMeasure;
OverallWidth : OPTIONAL IfcPositiveLengthMeasure;
PredefinedType : OPTIONAL IfcDoorTypeEnum;
OperationType : OPTIONAL IfcDoorTypeOperationEnum;
UserDefinedOperationType : OPTIONAL IfcLabel;
ENTITY IfcDoorStandardCase
END_ENTITY;

Link to this page  Link to this page